Design And Implementation Of Temperature Measuring Device Using Max6675 And Thermocouple On Wet Cooling Tower
Abstract
Colling Tower or cooling tower is a technology used in the industrial world, cooling tower works to cool water fluid by using wind power that comes from a fan or blower, how the cooling tower works is basically hot water coming from the machine is flowed to the cooling tower then water through the fill-fills that are in the cooling tower and in direct contact with the air, the cooling tower is focused on reducing the temperature of the inlet water until it leaves it, while the water temperature reading uses a thermocouple sensor. A thermocouple is a temperature sensor capable of reading temperatures from -200 ℃ to 1200 ℃. This cooling tower uses arduino mega circuit, PCB board, MAX6675 module and thermocouple. How to read the temperature on the cooling tower using a computer or laptop with Microsoft Excel that is already connected to the PLX-DAQ software. The data that has been obtained is then tested using SPSS (Statiscal Product and Service Solutions) software, testing using 3 types, namely normal distribution, standard deviation, and reliability. The overall results of the thermocouple sensor on the Wet Cooling Tower show normal performance according to statistical testing, including normal distribution, standard deviation, and reliability. All data and values obtained have met the established standards
Keywords
References
R. F. F. Pontes, W. M. Yamauchi, and E. K. G. Silva, “Analysis of the effect of seasonal climate changes on cooling tower efficiency, and strategies for reducing cooling tower power consumption,” Appl. Therm. Eng., vol. 161, p. 114148, 2019, doi: https://doi.org/10.1016/j.applthermaleng.2019.114148.
E. Novianarenti and G. Setyono, “Peningkatan Performansi Cooling Tower Tipe Induced Draft Counter Flow Menggunakan Variasi Bentuk Filler,” R.E.M (Rekayasa Energi Manufaktur) J., vol. 4, no. 1, 2019, doi: 10.21070/r.e.m.v4i1.1766.
E. K. Laksanawati, A. Sulaeman, and A. Rosydin, “Desain Rancang Bangun Cooling Tower menggunakan Aplikasi Autocad Skala Laboratorium Teknik Mesin Universitas Muhammadiyah Tangerang,” Mot. Bakar J. Tek. Mesin, vol. 6, no. 1, p. 37, 2022, doi: 10.31000/mbjtm.v6i1.6698.
G. J. Samola, L. S. Patras, and G. Mangindaan, “Analisa Sistem Pendingin Berdasarkan Besar Daya Lisrik Yang Di Bangkikan Pada PLTP Lahendong,” J. Tek. Elketro , pp. 1–10, 2022.
K. Umurani, A. Syuhada, M. I. Maulana, and Z. Fuadi, “Pengaruh Rasio Massa Air dan Udara Terhadap Unjuk Kerja Forced Draft Wet Cooling Sudut Inklinasi Splash Fill Berlubang,” in SEMINAR NASIONAL TEKNOKA, 2023, vol. 8, no. 2502, pp. 35–41.
Y. Rizkiya, “Bab II Landasan Teori,” J. Chem. Inf. Model., vol. 53, no. 9, pp. 1689–1699, 2019.
Y. Handoyo, “Analisis Performa Cooling Tower LCT 400 Pada P.T. XYZ, Tambun Bekasi,” J. Ilm. Tek. Mesin, vol. 3, no. 1, pp. 38–52, 2015.
A. Mursadin, “ANALISIS KINERJA COOLING TOWER MENGGUNAKAN METODE RANGE DAN PENDEKATAN DI PLTU ASAM-ASAM,” vol. 4, no. 2, pp. 15–27, 2022.
X. Chen, F. Sun, Y. Chen, and M. Gao, “Novel method for improving the cooling performance of natural draft wet cooling towers,” Appl. Therm. Eng., vol. 147, pp. 562–570, 2019.
W. Deng, F. Sun, K. Chen, and X. Zhang, “New retrofit method to cooling capacity improvement of mechanical draft wet cooling tower group,” Int. J. Heat Mass Transf., vol. 188, p. 122589, 2022, doi: https://doi.org/10.1016/j.ijheatmasstransfer.2022.122589.
Z. Yu et al., “Analysis of a novel combined heat exchange strategy applied for cooling towers,” Int. J. Heat Mass Transf., vol. 169, p. 120910, 2021, doi: https://doi.org/10.1016/j.ijheatmasstransfer.2021.120910.
T. Wu, Z. Ge, L. Yang, and X. Du, “Flow deflectors to release the negative defect of natural wind on large scale dry cooling tower,” Int. J. Heat Mass Transf., vol. 128, pp. 248–269, 2019, doi: https://doi.org/10.1016/j.ijheatmasstransfer.2018.09.009.
S. M, H. Tehuayo, M. Hasriadi, and N. Fadhilah, “Rancang bangun alat pengukur suhu air cooling tower berbasis IOT pada PT. Tirta Fresindo Jaya,” ILTEK J. Teknol., vol. 17, no. 1, pp. 11–14, 2022, doi: 10.47398/iltek.v17i1.663.
R. Septiana, I. Roihan, and J. Karnadi, “Calibration of K-Type Thermocouple and MAX6675 Module With Reference DS18B20 Thermistor Based on Arduino DAQ,” Pros. SNTTM XVIII, pp. 9–10, 2019.
H. Santoso and R. Ruslim, “Pembuatan Termokopel Berbahan Nikel (Ni) dan Tembaga (Cu) Sebagai Sensor Temperatur,” Indones. J. Fundam. Sci., vol. 5, no. 1, p. 59, 2019, doi: 10.26858/ijfs.v5i1.9376.
N. Wendri, I. wayan Supardi, K. N. Suarbawa, and N. M. Yuliantini, “Alat Pencatat Temperatur Otomatis menggunakan Termokopel berbasis Mikrokontroler AT89S51,” Bul. Fis., vol. 13, no. 1, pp. 29–33, 2012.
M. Noviyanti and ) Hufri, “Rancang Bangun Set Eksperimen Kalorimeter Digital Dengan Pengindera Sensor Termokopel Dan Sensor Load Cell Berbasis Arduino Uno,” Pillar Phys., vol. 13, no. April, pp. 34–41, 2020.
R. F. P. Khairul Umurani1, Rahmatullah, Ahmad Marabdi Siregar, Arya Rudi Nasution, “Perpindahan Panas dan Penurunan Tekanan Pada Plat Rata Dengan Media Berpori (Porous),” J. Rekayasa Mater. Manufaktur dan Energi, vol. 6, no. 1, pp. 89–98, 2023, doi: 10.30596/rmme.v6i1.13598.
A. M. Chaln Chavez and K. E. Guevara Paredes, “STUDI DESAIN SENSOR TERMOKOPEL TIPE K DAN KARAKTERISTIKNYA UNTUK ALAT DIFFERENTIAL THERMAL ANALYSIS (DTA),” 2014.
B. A. B. Ii, “BAB II TINJAUAN PUSTAKA 2.1 Pengertian Exhaust Gas Temperature,” pp. 5–31, 2013.
A. T. Basuki, “Penggunaan SPSS dalam Statistik,” Danisa Media, vol. 1, pp. 1–104, 2014.
R. Wuryaningrum and A. Budiarti, “Pengaruh Rasio Keuangan Terhadap Harga Saham Pada Perusahaan Farmasi di BEI,” J. Ilmu dan Ris. Manaj., vol. 4, no. 11, pp. 1–18, 2015.
I. K. Swarjana, “Konsep Pengetahuan Sikap, Prilaku, Persepsi, Stres, Kecamasan, Nyeri, Dukungan Sosial, Kepatuhan, Motivasi, Kepuasan, Pandemi Covid-19, Akses Layanan Kesehatan,” Andi, vol. 4, pp. 3–12, 2022.
E. Febriyanti and L. I. Purnomo, “Pengaruh Audit Complexity , Financial Distress , Dan Jenis Industri Terhadap Audit Delay,” SAKUNTALA Pros. Sarj. Akunt. Tugas Akhir Secara Berk., vol. 1, no. 1, pp. 645–663, 2021.
L. Amanda, F. Yanuar, and D. Devianto, “Uji Validitas dan Reliabilitas Tingkat Partisipasi Politik Masyarakat Kota Padang,” J. Mat. UNAND, vol. 8, no. 1, p. 179, 2019, doi: 10.25077/jmu.8.1.179-188.2019
DOI: https://doi.org/10.30596/rmme.v7i2.19801
Refbacks
- There are currently no refbacks.
This work is licensed under a Creative Commons Attribution 3.0 License
Jurnal Rekayasa Material, Manufaktur dan Energi is abstracting & indexing in the following databases:
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Statcounter View My Stats RMME